Inside a large metal building sprayed white, a person walking past the open bay doors.

Home / Shops and metal buildings

Spray foam insulation for shops, metal buildings and commercial buildings in El Campo, TexasFoam tight to steel.

Shady Oak Spray Foam insulates shops, metal buildings, warehouses, offices and stores from El Campo across the Texas Gulf Coast. On steel, closed cell is the usual choice, sprayed on the inside face of the wall panels and the underside of the roof. Call before the shelves, the lift and the tools move in.

100% recommend on Facebook, from 6 reviews

Pictured: a metal building we sprayed, walls and roof.

Shops and metal buildings

A metal building sweats when damp Gulf air touches steel that’s colder than the air’s dew point, so the foam goes straight on the steel, with no gap behind it.

Usually
Closed cell on the steel
Sprayed
Wall panels and underside of roof
Good time
Before the building fills up
Based in
El Campo, Texas

Why steel sweats

Cold steel, wet air.

Here’s why a metal building drips, and what closed cell on the inside face of the panel does about it.

Looking down on a metal building wall: the ribbed steel panel outside, closed cell foam sprayed on its inside face, and the steel girts behind it. OUTSIDEINSIDE Steel wall panel Closed cell foam Girt
Looking down on a metal building wall.
  • Where the water comes from

    A bare panel gives damp air a cold face to land on. When the steel’s colder than the air’s dew point, the water comes out right there.

  • Foam on the panel

    Closed cell is sprayed on the inside face of the panel and sticks tight to it, with no gap behind where damp air can sit against the steel.

  • Sealed panel laps

    Sprayed on the inside of the panels, foam insulates, seals the panel laps and slows outside air moving through the skin of the building.

  • Still needs air

    Foam cuts the sweating down. It doesn’t promise to end it. Wash equipment inside and the building still needs ventilation to move that wet air out.

What we spray

Steel first, then the laps and gaps.

On a metal building the foam goes on the inside face of the steel, walls and roof, end to end.

  • Wall panels

    Closed cell sprayed on the inside face of the steel, between the girts, tight to the panel.

  • Underside of the roof

    The underside of a screw-down roof, sprayed between the purlins from one end of the building to the other.

  • Panel laps and gaps

    Foam fills the laps and gaps where panels meet each other and the framing, the places outside air works its way in.

  • Warehouses and industrial

    Big open buildings sprayed wall to wall and overhead, held to the same standard as a small shop.

  • Offices and stores

    One seamless layer that seals cracks, gaps and voids, sprayed on a build-out before the sheetrock goes up.

  • Buildings already up

    Shops that are already standing get sprayed too, once trucks, tools and equipment are moved out or covered tight.

Our work

Shops we’ve sprayed.

Every picture in this row is a shop Shady Oak sprayed. Look at the walls and the underside of the roof.

A shop with foam across the underside of the roof between timber trusses, a stained floor.
Timber trusses, foam between them.
A shop with the lights on, white across the roof and walls, an overhead door at the far end.
Walls and roof, all white.
A metal shop with foam on the roof and walls, a plywood-faced wall along the back and an orange lift.
A shop with a plywood back wall.
A metal shop with foam on the roof and walls, an overhead door rolled up to a field, a red lift in the doorway.
Overhead door open, the lift still inside.

See all our work

Which foam

Steel changes the answer.

Open cell usually goes in attics and walls. A metal building is a different job, and here’s why the foam changes.

Closed cell

On steel, closed cell

Closed cell is the denser, firmer foam. It air seals, makes a stronger vapor barrier than open cell and sets up hard against what it’s sprayed on. It also costs more, so ask which parts of your building need it.

Open cell

  • What it’s likeLighter and softer. It expands more.
  • SealAir seal. Not a vapor barrier.
  • CostThe cheaper of the two.
  • Usually goesAttics and walls.

Closed cell

  • What it’s likeDenser and firmer, with a higher R-value.
  • SealAir seal, plus a stronger vapor barrier.
  • CostCosts more. Adds structural strength.
  • Usually goesMetal buildings, crawlspaces and basements.

Good to know

Foam will burn, so code generally wants it covered from the space people use, usually with sheetrock or an approved fire coating. Foam left showing in a shop may need one too. Ask about it before you spray.

Source: Spray Polyurethane Foam Alliance, FAQs.

Open cell or closed cell: the full comparison

How it goes

How a shop job goes.

Three steps, and the first one is a phone call with a few photos.

  1. You call

    Tell us where the building is, what kind it is and whether it’s up yet. Send a few photos of the inside if you have them.

  2. We look

    We look at the building and what you want out of it, comfort, humidity, sweating or cost, then tell you which foam goes where.

  3. We spray

    Foam goes on the wall panels and the underside of the roof, and the steel has to be clean and dry first. Trucks and tools get moved or covered, and you stay out until the crew says it’s clear.

Have ready when you call

  • Where the building is
  • Size, and whether it’s up yet
  • Photos of the inside walls and roof

Questions we get

Straight answers.

The ones people ask before they call a foam crew, answered in plain words.

Will spray foam stop my metal building from sweating?

It cuts the sweating down, and nobody honest promises more than that. Closed cell stuck to the panel keeps damp room air off the cold steel. A building that makes a lot of moisture inside still has to be ventilated.

Does the foam have to be covered, or can it stay exposed in my shop?

It depends on the foam and your local code. Foam is combustible, and code generally wants a barrier between it and the space people use. Some products are approved to stay exposed in certain spots. Ask us on the call.

What does it cost to spray a shop?

It depends on the building, so there’s no number on this page. The size, how much steel gets sprayed, which foam and how thick all move the price. Call with the location and photos and we’ll talk through yours.

When should a new shop get sprayed, and can you do one that’s already in use?

Both work. On a new shop, get the welding and cutting done first, because hot work on or near foam is a fire and fume hazard. A building in use gets sprayed too, with people out of the work area.

What do I have to move out before you spray?

Anything you don’t want foam on. Overspray doesn’t come off most surfaces, so vehicles, tools and equipment get moved out or masked, and pilot lights and open flames get shut off. We’ll go over who handles what before the job.

How long do we have to stay out of the building?

It depends on the foam and how well the building airs out, so there isn’t one figure. Nobody without protective gear works in the area while we spray or for a period after. We’ll give you the time for your job.

Can you spray any metal roof?

Not every one without checking. Screw-down panels are the normal case for foam. A standing seam roof built to float is different, so the panel maker gets asked before anyone sprays it.

Something we didn’t cover?

Call (210) 288-9665 and ask. It’s quicker than reading, and every building’s a little different.

Call about your building

Tell us about
your metal building.

Call with where it is, what kind of building it is and a few photos. We’ll tell you which foam goes where.

(210) 288-9665

“Best spray foam job I’ve ever seen.”

Patrick G., on Facebook, August 2024